|
 The Samurai Brush Guard is the perfect accessory for your stock front bumper.
This is a reproduction of the
factory Suzuki guard.
Works in conjunction with a stock bumper.The brushgaurd is designed to see light
duty.
Uses 1/4" frame mounting plates. and 1/4" uprights.
MOUNTING:
Another easy to install product. Simply remove the front bumper, then the
two tow brackets on the front frame rails and use the provided hardware kit
bolts to attach to the frame. Put the front bumper back on and assemble. |
MATERIAL:
Constructed of water jetted 1/4" cold rolled steel, with thick wall tubing on the headlight wraps. |
| |
Shipped in a raw steel condition ONLY. Clean off with mineral
spirits and paint using Rustoleum brand "Hammertone" paint for a
durable finish.
The Samurai Subspeed Winch bumper is the newest
addition to the ZOR product line.
This is a low profile front winch bumper without the normal uprights of the "PFSC" style. We will be designing two different Stinger options for it very soon. The one shown is the "SHOGUN" stinger. The bumper can be purchased with or without a stinger. Stingers are weld on ONLY!
The bumper and the "SHOGUN" stinger is available now! Both the "SHOGUN and the "NINJA" stingers are $99 (for a limited time during introduction). The "NINJA" Stinger will have a picture soon. It is narrower at the top.
Uses 1/4" frame mounting plates.
MOUNTING:
Another easy to install product. Simply remove the front bumper, then the
two tow brackets on the front frame rails and use the ZOR HD bolt kit
(extra $24.95) to attach to the frame. Put the front bumper back on and assemble. |
MATERIAL:
Constructed of water jetted 1/4" cold rolled steel. And your choice of Rock Crawler ends welded on. |
|
Shipped in a raw steel condition ONLY. Clean off with mineral
spirits and paint using Rustoleum brand "Hammertone" paint for a
durable finish.
 The BULLDOG is a great value bumper for replacing that old stock bumper.
The Bulldog shell is 1/8th" thick steel shell. Designed to see light
duty. It is available ONLY in a LED style. The Bulldog is NOT intended to use with a winch.
Uses 1/4" frame mounting plates.
The bumper ends are slanted back and up at the bottom for clearance.
DIMENSIONS:
Dimensions are 7 high by 53.250. |
MATERIAL:
Constructed of cold roll steel, 100 ton CNC punch pressed than
folded on a 100 ton press. |
MOUNTING:
Another easy to install product. Simply remove the two tow brackets
on the front frame rails and use the same bolts to attach to the frame. |
COST:
|
Shipped in a raw steel condition ONLY. Clean off with mineral
spirits and paint using Rustoleum brand "Hammertone" paint for a
durable finish.
 PREFAB
CENTER SECTION
Our best selling ZOR product!
We call this the prefab
center section. It has seen many design changes over the last few years
including a winch plate and fairlead bracket. You can now choose from 3 different bumper end styles (see below) including the brand new "Solid Face" end.
This center section was designed to hug the front of the Samurai
allowing the most possible clearance when ledge crawling. Built for
winches pulling up to 9,000 lbs (some winch brands up to 9,500
lbs).*
If your winch is smaller, you can re-drill and center the winch very
easily. There are two sets of slotted holes. They are predrilled
off-center using the industry standard mounting pattern and centered
to the same pattern allowing complete versatility in your winch
installation. The fairlead slot and holes are centered to the
vehicle.
* Any winches or towing
using the ZOR center section should use the ZOR heavy duty bolting
system. No fairlead or winch provided. ZOR recommends ONLY a roller
fairlead be used with this center section.
MATERIAL:
Upper and lower steel tubing fully welded.
Constructed of 3/16th cold roll steel, 100 ton CNC punch
pressed than folded on a 100 ton press.
All ZOR bumpers with uprights use .250" CNC Plasma cut steel mounting plates.
All ZOR front bumper options can be installed. |
MOUNTING:
Another easy to install product. Simply remove the two tow
brackets on the front frame rails and use the same bolts to
reattach the ZOR front center section. |
DIMENSIONS:
Interior dimensions are 13.5 high by 22 .625. |
COST: |
Shipped in a raw
steel condition ONLY. Clean off with mineral spirits and paint using Rustoleum brand "Hammertone"
paint for a durable finish.
CENTER SECTION
& LED ROCK CRAWLER ENDS
These ends are welded onto the center section.
Designed to use LED or Oval type bulbed turn
signals.
Requires rubber boots and connectors, we can supply or tell you where to get them.
MATERIAL:
3/16th" high grade steel
punch pressed to specifications
then folded on a 100 ton press. |
COST: |
CENTER
SECTION & STOCK ROCK CRAWLER ENDS
These ends are welded onto the center section.
Designed to use your
existing Samurai turn signals.
Slant in two different directions, up and back, and have solid steel
end plates.
INCLUDED:
turn signal protectors screens
stainless steel hardware
MATERIAL:
3/16th" high grade steel
punch pressed to specifications
then folded on a 100 ton press. |
COST: |
CENTER SECTION & HEAVY DUTY CLASS 3 RECEIVER
This is our top of the line bumper. Needless to say your going to be seeing this one out on the trails.
The Receiver is welded at all touching seams and is reinforced with a thick wall square tube.
All styles of Rock Crawler ends are included with this price. Shown with the new "NO LIGHT" Rock Crawler ends
Designed to use for extreme pulling and pushing.
OPTIONAL:
Heavy Duty 5/8th" D-Rings double welded for optimum strength.
MOUNTING:
Another easy to install product. The ZOR HD Bolt Kit is a must for this bumper. |
COST:
|
Shipped in a raw steel condition ONLY. Clean off with mineral
spirits and paint using Rustoleum brand "Hammertone"
paint for a durable finish.
"Brute"
Front Bumper
You can order a "Big Brute" with the class 3 receiver or the "Little Brute" without the
class 3 receiver. All the ZOR options like the HD bolt kit, the
fender protectors, and the rock crawler ends are available.
The class 3 reciever is supported by additional thick wall square
tubing welded between the uprights.
This is another simple bolt on product that will turn heads and give
your zuk some muscle against trees and rocks.
Fully welded and made with the same procedures and materials as our
Prefab bumper. No drilling required to mount.
Shipped in a raw steel condition ONLY. Clean off with mineral spirits and paint using Rustoleum brand "Hammertone" paint for a durable finish.
HEAVY DUTY BOLT KIT
This front bumper bolting system is a must if you plan on towing,
yanking on D rings, or using a winch on your Samurai.
This is a retro fit kit for all previously manufactured ZOR front bumpers!
Designed to fit all Samurai frames.
MATERIAL:
Grade 8 3/8-16 bolts (2 with ground down heads to fit through frame rails)
Grade 8 washers, lock washers and nuts 4 precision (cnc lathe) steel spacers. |
COST:
|
FENDER PROTECTORS
These ZOR Fender Protectors bolt directly to the "Original"
or the
"Pre-Fab" or "Brute" styles of ZOR center sections.
MATERIAL:
1/4" Steel flat bar (cnc drilled to tight specifications)
thick wall tubing fully welded
tight bend radius
Superior protection for your Samurai fenders. Smasher Canyon
tested.
Stainless steel hardware provided. |
DIMENSIONS:
12&1/2" high by 15& 1/4 " wide |
|
COST:
|
|
